Part Number: PA015/PA035

Vehicle Applications:

2006-2011 Honda8th GenCivicFront(Fits all trims DX, DX-G, LX, EX, EX-L, and Si)

2011-2015 Honda9th GenCivic Front (Fits all trims DX, LX, EX, EX-L, and Si)

2016-2021 Honda 10th Gen Civic Front (Fits all trims FC7/FK6/FC1/FC3/FK4/FK7/FC6/FK5/FC2/FC4, except FK8 Type R)

2022-Present Honda 11th Gen Civic (FE/FL) Front

2022- Acura Integra A-Spec 1.5T

2007-2011 HondaCivic Type R FN2 Front

Paragon Track Performance Big Brake Kit (PA015 / PA035 6 piston) -Honda 8/9/10/11th Gen Civic Front

Paragon Track Performance Big Brake Kits offer superior braking performance specifically designed for track day enthusiasts. Come complete with every component required to upgrade your brake system. Developed with performance, quality, and longevity in mind, only the finest materials/components were used to ensure the brake kits to perform and last under both street and track conditions.

• Features Paragon PA015 / PA035 6 piston calipers*Only difference between the PA015 and PA035 calipers is the maximum rotor size they can accommodate

• Fully-floating 2-piece rotors, with directional ventilation vanes for optimal cooling performance. Runs up to 30% cooler than O.E. rotors

• Hard anodized/ENP nickel plated calipers, and hard anodized rotor hats for increased resistance to wear and discoloration under extreme track conditions

• Piston sizes optimized for each application. Designed to work flawlessly with OEM ABS and brake master cylinder. Compatible with OEM rear brakes

• Confidence-inspiring heat resistance during extended sessions. Optimum bite, modulation characteristics, thermal stability, and durability

• Recommended usage: Street / Track

• Complete pre-assembled axle set

Includes:

• One pair of Paragon PA015 / PA035 6 piston calipers

• One pair of Paragon fully-floating 2-piece rotor assemblies with hard anodized 6061-T6 aerospace grade aluminum hats, stainless steel bobbins, and anti-rattle clips

• One set of Paragon P3 Street/Track semi-metallic brake pads (manufactured by Winmax Japan, other compounds available at additional cost)

• One pair of caliper mounting brackets and all necessary hardware

• One pair of Goodridge DOT approved stainless steel braided brake lines

• One set of caliper anti rattle clips

• Detailed installation manual

***Please verify wheel fitment / clearance before ordering. All Paragon big brake kits are custom made/packaged to order, and cannot be returned due to wheel fitment issues.

**343mm brake kits generally require 17″ or larger wheels, while355mm / 370mm brake kits generally require 18″ or larger wheels.Fitment varies due to different specs / wheel design. Verify fitment with wheel fitment template.

Kit Number:

• PBK.02.055.343.320.TL.01.02.Px.F (343x32mm Rotor)

• PBK.02.055.355.320.TL.01.02.Px.F (355x32mm Rotor)

• PBK.05.055.370.360.TL.01.02.Px.F (370x36mm Rotor)

PA015 / PA035 6 Piston Calipers

• Mil-Spec hard coat anodized or ENP electroless nickel plated finish

• CNC machined from billet 6061-T6 aluminum

• Outstanding rigidity. Reduces compliance which allow for a consistent pedal feel, and improves responsiveness/modulation characteristics

• Titanium nitride (TiN) coated pistons. Improve durability and extend service intervals by protecting the sliding surfaces of the pistons. Allow smooth piston travel

• Stainless steel pistons can act as an effective thermal barrier due to the lower thermal conductivity vs. aluminum pistons, which help prevent brake fluid boiling and brake fade. Extra machining is done to minimize contact with the pads

• Staggered piston bore sizes for improved brake balance and even pad wear

• High temperature piston seals and internal dust seals are utilized to withstand the heat generated under harsh track conditions and extend caliper service life. Internal dust seals are able to offer protection against debris/contaminants and will not melt as easily as the external dust boots that are commonly used on OEM calipers

• Hard anodized/nickel plated for improved wear resistance. Will not deteriorate under extreme heat like painted/powder coated calipers

• Replaceable stainless steel abutment plates to allow smooth braking action and prevent wear on the caliper body

• Strong, yet lightweight. Each caliper weighs 6.5 lbs (without pads)

• Optional anti-knockback springs

• Stainless steel bleed screws and crossover pipes

• Each caliper is pressure tested to guarantee proper operation

ENP caliper finish

• Extremely durable and resistant to heat, wear, and corrosion

• More scratch resistant vs. hard anodized finish

• Easy wipe off of brake dust, brake fluid stain, and grime due to the low porosity of the plating

• Visually stunning finish which never deteriorates. Blends perfectly with any vehicle’s color scheme

Floating 2-piece Rotors

• Floating 2-piece design allows thermal expansion of the rotor while minimizing deformation and ensuring the rotor is self-centered with the pads

• Superior braking and cooling performance

• Features 72 directional ventilation vanes to create suction, turbulence, and guides cool air through the rotor for improved heat dissipation and increased resistance to cracking

• Made of CM-250 special formulated high carbon alloy cast iron. Allows for an optimal bite, thermal characteristics, high-temperature strength, and durability

• Heat treated to release stress in the rotor to avoid deformation and vibration

• State-of-the-art CBN surface machining to ensure better break-in with new brake pads

• Excellent thermal capacity.Allows the rotors to absorb and dissipate heat more efficiently and help reduce chance of brake fade

• Replacement rotor rings available at competitive price

Curved Directional Ventilation Vanes

Features 72 directional ventilation vanes to create suction and turbulence, and guide cool air through the rotor to achieve better heat dissipation and increased resistance to cracking under harsh track conditions. Each rotor is left or right side specific, and the ventilation vanes are optimized to spin in a particular direction to pump the maximum amount of cool air through the rotor. This design allows the rotor to run up to 30% cooler than O.E. rotors and increases cooling efficiency by up to 30% over standard 1-piece units. Brake fade and judder are minimized during extended sessions. This means the brake system can withstand heavier track usage and provide consistent braking performance lap after lap.

Slotted Friction Face

Slotted rotor face pattern improves brake consistency by constantly cleaning the contact surface and dissipate heat generated, and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface.

Hard Anodized Aluminum Hats

• CNC machined from lightweight 6061-T6 aerospace grade aluminum

• Unsprung weight reduction

• High strength and durability

• Type III Mil-spechard anodized to increase resistance to wear, corrosion, and discoloration

Floating Bobbins & Mounting System

Utilizes T-Bobbin rotor to hat mounting system to allow “float” in both radial and axial directions, and minimize brake judder. The high quality stainless steel hardware are corrosion resistant which allows secure mounting, and smooth expansion and contraction throughout heat cycles. Anti wear clips (McLaren spring clips) are utilized to slightly pre-load the rotor assembly and minimize rattling noise.

Caliper Mounting Brackets

CNC machined caliper mounting brackets to ensure superior strength, durability, and secure mounting of calipers to knuckles.

Paragon Brake Pads

• Manufactured by Winmax Japan

• Superior stopping power and modulation

• High fade resistance

• Consistent performance under high temperature conditions

• Compounds available for street, street / track, and dedicated track applications

• PA015 / PA035 caliper uses a common pad shape, with compounds readily available from various manufacturers

Goodridge Stainless Steel Braided Brake Lines

• Superior durability. Abrasion and corrosion resistant

• Allows more responsive and firmer pedal feel

• DOT / TV certified

Paragon Brake PadCompounds:

P2 Compound

The P2 Sport Comfort compound is designed for street use where balance between performance and street friendliness is emphasized. Minimal brake dust and noise due to its non-metallic material. Improved initial bite, modulation (brake control), and temperature range over stock pads. Higher coefficient of friction for increased stopping power. Excellent pad and rotor life. Works as designed from ambient temperature. Ideal for daily driven vehicles with performance in mind.

• Material: Non-metallic

• Effective temperature range: Ambient – 932F (500C)

• Average Mu: 0.29 ~ 0.32

• Recommended for street use only

• Comparable to: Hawk HPS, Project Mu B Spec

P3 Compound

The P3 Road & Track compound is an all round compound ideal for sport driving, autocross, and light track duty while still maintaining street drivability. Low level of brake dust and noise. Good coefficient of friction, initial bite, and temperature range make this compound capable for track conditions. Best modulation and control characteristics among P series compounds. Great choice for occasional track vehicles without the disadvantages of dedicated track pads. Works as designed from ambient temperature. Great rear pad option for those who prefer a more front biased setup with the R5 compound up front.

• Material: Semi-metallic

• Effective temperature range: Ambient – 1112F (600C)

• Average Mu: 0.34 ~ 0.37

• Recommended for street / track use

• Comparable to: Ferodo DS2500, Endless MXRS & MX72, Project Mu HC+, PFC 97, Hawk HP+, Pagid RS4-2

R5 Compound

The R5 High Friction Track / Competition compound is designed as a dedicated track compound. High coefficient of friction provides sufficient stopping power for track and competition conditions. Precise modulation and release characteristics. Highly fade resistant with wide temperature range. Flatter torque curve compared to the R7 compound, providing consistent and solid braking performance throughout the effective temperature range which boosts drivers confidence. Elevated noise and brake dust compared to P2 and P3 compounds. Relatively easy on rotors compared to competitors racing pad offerings. Great front pad option for lighter cars, and rear pad option for those who prefer a more front biased setup with the R7 compound up front.

• Material: Metallic

• Effective temperature range: 212F – 1382F (100C – 750C)

• Average Mu: 0.40 ~ 0.43

• Recommended for track use

• Comparable to: Endless CC38(ME22) & CC-Rg, Project Mu Racing 777, Ferodo DSUNO & DS3000 , Cobalt XR3 & XR4, Pagid RST3, RS44 & RS19, CL RC6

R7 Compound:

The R7 Maximum Friction Track / Competition compound is a full race compound with maximum coefficient of friction. With higher stopping power and maximum effective operating temperature, the R7 compound is ideal for advanced high speed track events, competitions, and heavier cars that require maximum braking performance. Good modulation and release characteristics. Excellent pad and rotor life. Higher fade resistance compared to the R5 compound, with solid pedal feel throughout the effective temperature range.

Material: Metallic

• Effective temperature range: 212F – 1562F (100C – 850C)

• Average Mu: 0.48 ~ 0.53

• Recommended for track use only

• Comparable to: Endless CC60(N30C), Cobalt XR1 & XR2, Pagid RS29, Ferodo DS3000+

***Track and race pads are not recommended to be used on streets due to elevated brake dust and noise level, possibly higher pad and rotor wear during low speed brake events, and being not able to work 100% as designed at ambient temperature. If these downsides of dedicated track and race pads are not an issue, they can be used on streets absolutely fine.